移動式攪拌站是一種將混凝土攪拌站的物料儲料、稱量、輸送、攪拌、卸料及全自動控制系統整體集中與一個拖掛單元的混凝土生產設備。

型號Model HZS050-3Y
理論生產率Max theory Capacity (m3/h) 50
攪拌主機Mixer JS1000
儲料倉容積Storage hopper capacity (m3) 4×8
骨料大粒徑（卵石/碎石）Aggregate Max. Dia (pebble/crushed) 80/60mm
卸料高度Discharge height (m) 4
上料高度Charge height (m) 5.4
骨料計量精度Aggregate measuring accuracy (%) ±2
粉料計量精度Cement measuring accuracy (%) ±1
水計量精度Water measuring accuracy (%) ±1
外加劑計量精度Additive measuring accuracy (%) ±1
整機功率(不含水泥倉螺旋)Power of supply (kW) ( without cement silo and screw conveyor) 68
電壓/頻率Power voltage (V) /frequency (Hz) AC 380/50
整機重量(不含水泥倉螺旋)Total weight(t) about ( without cement silo and screw conveyor) 28.2

注：1. 產品按國家標準GB/T10171-2005及合同約定執行；
Note:1.Products are manufactured according to China state standard GB/T10171-2005.
2. .國家標準及合同中未約定部分按生產廠家產品參數執行；
2. All the parts which are not stipulated in the above or in the State standard are according to the manufacturer’s design.
3.由于技術改進原因，外購件型號、技術參數、產地可能有改變，但不低于現有功能
3 All the parts and specification may be changed without notification due to technical improvement , but not lower than the above configuration.
4、買方需自備以下設施：The buyer should provide the following facilities
（1）攪拌站的混凝土基礎、到攪拌站配電柜的電源及攪拌站水源；
（1）the foundation of concrete batching plant, the power and water supplying point according to our foundation drawing.
（2）到攪拌站內的避雷系統；
（2）Lightning protection system
（3）根據國家標準進行的重量校準測量及校準的費用；
（3）Scales calibration is carried out according local standard on buyer’s expenses.
1.本設備建議采用三相五線制配電電源,單根電源線采用線徑不小于95mm2 的銅線，電源變壓器容量不小于200kVA，變壓器距離攪拌樓不大于100米，否則需增粗線徑。
The plant is suggested to adopt three phases five wires power supply , the single power line diameter is not less than 95mm2 of copper cable, and the capability of the transformer is not less than 200kVA. The distance between transformer and concrete batching plant should be less than 100 meters, otherwise the cable diameter should be increased.
6、以上配置按中國國內電源參數（電壓380V/220V，頻率50Hz）設置，如電源參數與此不符，需提前告知我公司。
The power source for all electrical components and motors is 380 V / 220 V, 50 Hz, If power source is different, please inform our company in advance.